Performance Analysis of The Hairpin Heat Exchanger Using Different Nano Fluids

P. Kiranbabu; V. Sivaprasad; Raghuram Pradhan; L. Ramprasad Reddy; S. Kondala Rao; Yarram Srinivasa Reddy

doi:10.55524/ijircst.2022.10.3.61

Abstract

An apparatus that moves heat from one fluid to another is a heat exchanger. To avoid mixing, the fluids may be separated by a solid wall, or they may be in direct touchHairpin Exchangers are available in bare tubes, finned tubes, U-tubes, straight tubes (with rod-thru capability), fixed tube sheets, and detachable bundles. They also come in single tubes (Double Pipe) and numerous tubes within a hairpin shell (Multitude). The combination characteristics of nano fluid and base fluid water are calculated in this article. Magnesium Oxide and silver nano particle volume fractions of 0.35, 0.45, 0.55, and 0.65 percent at varied velocities (0.5, 1,1.5, and 2 m/s) were used as nano fluids. The properties of nanofluids are calculated theoretically, and the results are used as inputs for analysisA 3D model of the hair pin heat exchanger with and without twisted tape is made using CREO parametric software. CFD analysis of the hair pin heat exchanger is performed at different nanofluid volume fractions. The pressure drop, Reynolds number, heat transfer coefficient, and Nusselt number are all determined using CFD analysis.

Keywords

Hair pin heat exchanger, CFD study, and finite element analysis.

References

A.O. Adelaja, S. J. Ojolo and M. G. Sobamowo, "PC Aided Analysis of Thermal and Mechanical Design of Shell and Tube Heat Exchangers", Advanced Materials Vol. 367 (2012) pp 731-737 © (2012) Trans Tech Publications, Switzerland.
Yusuf Ali Kara, Ozbilen Guraras, "A PC program for structuring of Shell and cylinder heat exchanger", Applied Thermal Engineering 24(2004) 1797–1805
Rajagapal THUNDIL KARUPPA RAJ and Srikanth GANNE, "Shell side numerical investigation of a shell and cylinder heat exchanger considering the impacts of perplex tendency edge on liquid stream", Thundil Karuppa Raj, R., et al: Shell Side Numerical Analysis of a Shell and Tube Heat Exchanger, THERMAL SCIENCE: Year 2012, Vol. 16, No. 4, pp. 1165-1174.
S. Noie Baghban, M. Moghiman and E. Salehi, " Thermal investigation of shell-side progression of shell-and cylinder heat exchanger utilizing trial and hypothetical strategies" (Received: October 1, 1998 - Accepted in Revised Form: June 3, 1999).
A. GopiChand, Prof. A.V.N.L. Sharma, G. Vijay Kumar, A. Srividya, "Warm examination of shell and cylinder heat exchanger utilizing mat lab and floefd software”, Volume: 1 Issue: 3 276 – 281, ISSN: 2319 – 1163.
Hari Haran, Ravindra Reddy and Sreehari, "Warm Analysis of Shell and Tube Heat Exchanger Using C and ANSYS”, International Journal of Computer Trends and Technology (IJCTT) – volume 4 Issue 7–July 2013.
Donald Q.Kern. 1965. Procedure Heat move (23rdprinting 1986). McGraw-Hill companies. ISBN 0-07-Y85353-3.
Richard C. Byrne Secretary. 1968. Cylindrical Exchanger Manufacturers Association, INC. (eighth Edition). 25 North Broadway Tarrytown, New York 10591.
R.H Perry. 1984. Perry's Chemical Engineer's Handbook (sixth Edition Ed.). McGraw-Hill. ISBN 0-07-049479-7.
Ender Ozden, Ilker Tari, Shell Side CFD Analysis of A Small Shell And Tube Heat Exchanger, Middle East Technical University, 2010.

Cites this article as

P. Kiranbabu, V. Sivaprasad, R. Pradhan, L. R. Reddy, S. K. Rao, Y. S. Reddy, "Performance Analysis of The Hairpin Heat Exchanger Using Different Nano Fluids", International Journal of Innovative Research in Computer Science and Technology (IJIRCST), Vol-10, Issue-3, Page No-386-392, 2022. Available from: https://doi.org/10.55524/ijircst.2022.10.3.61

Corresponding Author

P. Kiranbabu

Professor, Department of Mechanical Engineering, Pace Institute of Technology and Sciences (Autonomous), Ongole, Andhra Pradesh, India

Download Full Paper

Download PDF

No. of Downloads: 32 | No. of Views: 1264

Performance Analysis of The Hairpin Heat Exchanger Using Different Nano Fluids

Citations

Total View 1264

Total Download 32